Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
They are making a number of great pointers relating to Installing A Bathtub in general in the article on the next paragraphs.
Installing a bathtub isn't precisely rocket science, however it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a new one is likewise a moderately hard task. If the old tub is easily easily accessible, the task can move speedily; if you have to open up a wall to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need a helper to leave the old bathtub and set in the new one. Ensure you have actually certified on your own for the work as well as fit attempting it. Instead of employing a contractor to take control of a halfway-completed task, it is far better to think about utilizing one before you start. Chances are you may require a specialist plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have actually already gotten a new bathtub as well as don't require to change the setup of your previous water pipes.
Your tools as well as product checklist ought to consist of the following:
Preparing for the Setup
Firstly, the supporting framework supplied with the bathroom must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited accessibility that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the required position. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bathtub up until the level checks out level.
To mount faucets, fit all-time low of the furthest flexible tap connector to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water supply and also inspect all joints and also new pipework for leaks and tighten them if essential. Load the bathtub and additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as described in the producer's user's manual. Tiling as well as securing around the tub should wait up until the tub has actually been utilized at least once as this will settle it into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area between the tap as well as the sink. Safeguard the tap in place with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The former type needs to be linked to the faucet ends initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a stiff seal, creating the water to pass through the wall surface between the bath as well as the tiling, bring about difficulties with dampness and also possible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealant can crack relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the marketplace. It is a good idea to fit the tiles using water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that piece on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the internet. If you enjoyed our page if you please be sure to share it. We value reading our article about How to Install a Bathtub Yourself.
Protect plumbing integrity; connect now. Report this page